manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

4AT(diag)-39

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

AUTOMATIC TRANSMISSION (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK HARNESS CONNECTOR BETWEEN 
TCM AND ATF TEMPERATURE SENSOR.

1) Turn the ignition switch to OFF.
2) Disconnect the connector from transmission 
and TCM.
3) Measure the resistance of harness between 
TCM and transmission connector.

Connector & terminal

(B55) No. 12 — (B11) No. 15:
(B55) No. 23 — (B11) No. 11:

Is the resistance less than 1 

:

? Go to step 

2

.

Repair the open 
circuit of harness 
between TCM and 
transmission con-
nector.

2

CHECK ATF TEMPERATURE SENSOR.

1) Turn the ignition switch to OFF.
2) Connect the connectors to transmission and 
TCM.
3) Start the engine.
4) Warm up the transmission until the ATF 
temperature exceeds 80°C (176°F).
5) Disconnect the connector from transmis-
sion.
6) Measure the resistance between transmis-
sion connector terminals.

Connector & terminal

(T4) No. 11 — No. 15:

Is the resistance 300 — 800 

:

? Go to step 

3

.

Go to step 

6

.

3

CHECK ATF TEMPERATURE SENSOR.

Measure the resistance between transmission 
connector terminals.

Connector & terminal

(T4) No. 11 — No. 15:

Does the resistance value 
increase while the ATF temper-
ature decreases?

Go to step 

4

.

Go to step 

6

.

4

CHECK INPUT SIGNAL FOR TCM.

1) Connect the connector to transmission.
2) Connect the Subaru Select Monitor to data 
link connector.
3) Turn the ignition switch to ON.
4) Read the data of “ATF temperature sensor” 
using Subaru Select Monitor.

Does the ATF temperature 
gradually decrease?

Check the connec-
tors or harnesses 
between ATF tem-
perature sensor 
and transmission, 
and repair the 
defective part.

Go to step 

5

.

5

CHECK HARNESS CONNECTOR BETWEEN 
TRANSMISSION AND ATF TEMPERATURE 
SENSOR.

1) Turn the ignition switch to OFF.
2) Disconnect the connector from transmis-
sion.
3) Remove the transmission connector from 
bracket.
4) Lift up the vehicle.
5) Drain the automatic transmission fluid.

CAUTION:
Do not drain ATF until it cools down.

6) Remove the oil pan.
7) Disconnect the control valve connector.
8) Measure the resistance of harness between 
ATF temperature sensor and transmission con-
nector.

Connector & terminal

(T4) No. 11 — (AT2) No. 4:
(T4) No. 15 — (AT2) No. 9:

Is the resistance less than 1 

:

? Replace the con-

trol valve body. 
<Ref. to 4AT-58, 
Control Valve 
Body.>

Repair the open 
circuit of harness 
between ATF tem-
perature sensor 
and transmission 
connector.

6

CHECK POOR CONTACT.

Is there poor contact of ATF 
temperature sensor circuit?

Repair the poor 
contact.

Replace the TCM. 
<Ref. to 4AT-63, 
Transmission Con-
trol Module 
(TCM).>

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
iDataLink maestro Rr Install Manual preview
maestro Rr
Бренд: iDataLink Страницы: 106
Edelbrock For 1985-1992 GM Cars and Trucks 17933 Installation Instructions preview
For 1985-1992 GM Cars and Trucks 17933
Бренд: Edelbrock Страницы: 4
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
Jeep Cherokee 1977 Owner'S Manual preview
Cherokee 1977
Бренд: Jeep Страницы: 136
Subaru 1994 Impreza Supplemental Service Manual preview
1994 Impreza
Бренд: Subaru Страницы: 540
r.LiNK RL2-NBT Manual preview
RL2-NBT
Бренд: r.LiNK Страницы: 20
Mopar 82214480 Manual preview
82214480
Бренд: Mopar Страницы: 17
Saab 2006 9-5 Owner'S Manual preview
2006 9-5
Бренд: Saab Страницы: 288
MBRP 0130717 Assembly preview
0130717
Бренд: MBRP Страницы: 5
Volvo 1997 850 Service Manual preview
1997 850
Бренд: Volvo Страницы: 62
Volvo Ski box Installation Instructions Manual preview
Ski box
Бренд: Volvo Страницы: 7
Curt Manufacturing 58987 Installation Manual preview
58987
Бренд: Curt Manufacturing Страницы: 4
Rola RCLSH Fitting Instructions preview
RCLSH
Бренд: Rola Страницы: 2
Classic Accessories 80-485-142401-RT Instructions Manual preview
80-485-142401-RT
Бренд: Classic Accessories Страницы: 14
Whispbar K509 Fitting Instructions Manual preview
K509
Бренд: Whispbar Страницы: 34
DIGITAL DELAY 1014-SCR Instructions Manual preview
1014-SCR
Бренд: DIGITAL DELAY Страницы: 11
Federal Signal Corporation CAMLCD-AHD-70 Installation And Operation Manual preview
CAMLCD-AHD-70
Бренд: Federal Signal Corporation Страницы: 68

Бренды по названию

Популярные бренды

Загрузить еще бренды