manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

SC(H4SO)-22

Battery

STARTING/CHARGING SYSTEMS

4. Battery

A: REMOVAL

1) Disconnect the positive (+) terminal after discon-
necting the negative (–) terminal of battery.
2) Remove the harness clip of the negative termi-
nal from the battery rod.
3) Remove the flange nut from battery rod and re-
move battery holder.

4) Remove the battery.

B: INSTALLATION

Install in the reverse order of removal.

Tightening torque:

3.5 N·m (0.4 kgf-m, 2.6 ft-lb)

NOTE:
• Clean the battery cable terminals and apply
grease to retard the formation of corrosion.
• Connect the positive (+) terminal, and then con-
nect the negative (–) terminal of the battery.
• After the battery is installed, initial diagnosis of
the electronic throttle control is performed. Wait for
10 seconds or more after turning the ignition switch
to ON, and then start the engine.

C: INSPECTION

WARNING:
• Electrolyte is corrosive acid, and has toxici-
ty; be careful of handling the fluid.
• Make sure the electrode does not come into
contact with skin, eyes or clothing. Especially
at contact with eyes, flush with water for 15
minutes and get prompt medical attention.
• In addition, be careful not to let the electrode
contact with the coated parts.
• Be careful when handling the batteries be-
cause they produce explosive gases.
• Be sure to keep battery away from any fire.
• For safety, in case an explosion does occur,
wear eye protection or shield your eyes when
working near any battery. In addition, never
lean over the battery.
• Ventilate sufficiently when using or charging
battery in enclosed space.
• Before starting work, remove rings, metal
watch-bands, and other metal jewelry.
• Never allow metal tools to contact the posi-
tive battery terminal and anything connected to
it while you are at the same time in contact with
any other metallic portion of the vehicle.

1. EXTERNAL PARTS

Check the battery case, top cover, vent plugs, and
terminal posts for dirt or cracks. If necessary, clean
with water and wipe with a dry cloth.
Apply a thin coat of grease on the terminal posts to
prevent corrosion.

2. ELECTROLYTE LEVEL

Check the electrolyte level in each cell. If the level
is below MIN level, bring the level to MAX level by
pouring distilled water into the battery cell. Do not
fill beyond MAX level.

3. SPECIFIC GRAVITY OF ELECTROLYTE

1) Measure specific gravity of electrolyte using a
hydrometer and a thermometer.
Specific gravity varies with temperature of electro-
lyte so that it must be corrected at 20°C (68°F) us-
ing the following calculation:

S

20

 = St + 0.0007 × (t – 20)

S

20

: Specific gravity corrected at electrolyte 

temperature of 20°C
St: Measured specific gravity
t: Measured temperature (°C)
Judge whether or not the battery requires 
charging according to corrected specific 
gravity.
Standard specific gravity: 1.220 — 1.290 
[at 20°C (68°F)]

SC-02238

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

A-Tach Mounts 50131 Instructions preview
50131
Бренд: A-Tach Mounts Страницы: 2
Suzuki Movano Owner'S Manual preview
Movano
Бренд: Suzuki Страницы: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Бренд: Torklift Страницы: 16
Cadillac 2012 Escalade Hybrid Manual preview
2012 Escalade Hybrid
Бренд: Cadillac Страницы: 90
BMW Wireless Charging Station Universal Instructions For Use Manual preview
Wireless Charging Station Universal
Бренд: BMW Страницы: 160
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Бренд: AC Schnitzer Страницы: 20
K&M MILSCO KIT# C746700 Installation Manual preview
MILSCO KIT# C746700
Бренд: K&M Страницы: 2
Car-Interface CI-RL4-NAC12 Manual preview
CI-RL4-NAC12
Бренд: Car-Interface Страницы: 25
Thule 2 Bike Carrier 977 Instructions Manual preview
2 Bike Carrier 977
Бренд: Thule Страницы: 6
Ecco Vantage 12 Series Installation And Operation Instructions preview
Vantage 12 Series
Бренд: Ecco Страницы: 5
Cadillac Escalade ESV 2014 Owner'S Manual preview
Escalade ESV 2014
Бренд: Cadillac Страницы: 508
Hama Liberty III Quick Start Manual preview
Liberty III
Бренд: Hama Страницы: 2
WABCO Truck Training Model Operating Instructions Manual preview
Truck Training Model
Бренд: WABCO Страницы: 56
Velleman CARS4500 User Manual preview
CARS4500
Бренд: Velleman Страницы: 12
Yakima K614 Manual preview
K614
Бренд: Yakima Страницы: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Бренд: FALCON RIDGE Страницы: 6
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Бренд: v.link Страницы: 21
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440

Бренды по названию

Популярные бренды

Загрузить еще бренды