manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

4AT(diag)-59

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

AUTOMATIC TRANSMISSION (DIAGNOSTICS)

4

CHECK OUTPUT SIGNAL OF TCM.

1) Connect the connectors to TCM and trans-
mission.
2) Connect the Subaru Select Monitor to data 
link connector.
3) Start the engine.
4) Run the Subaru Select Monitor.
5) Warm up the transmission until the ATF 
temperature exceeds approximately 80°C 
(176°F).
6) Stop the engine.
7) Turn the ignition switch to ON.
8) Shift the select lever to “P” or “N” range, and 
depress the accelerator pedal.
9) Read the data of “Low Clutch Duty” using 
Subaru Select Monitor.

Is the measured value 100%?

Go to step 

5

.

Go to step 

6

.

5

CHECK OUTPUT SIGNAL FROM TCM US-
ING SUBARU SELECT MONITOR.

1) Turn the ignition switch to ON.
2) Set the select lever to the “D” range.
3) Read the data of “Low Clutch Duty” using 
Subaru Select Monitor.

Is the measured value 0%?

Check the har-
nesses or connec-
tors between TCM 
and transmission, 
and repair the 
defective part.

Go to step 

6

.

6

CHECK POOR CONTACT.

Is there poor contact of low 
clutch duty solenoid circuit?

Repair the poor 
contact.

Replace the TCM. 
<Ref. to 4AT-63, 
Transmission Con-
trol Module 
(TCM).>

7

CHECK LOW CLUTCH DUTY SOLENOID (IN 
TRANSMISSION).

1) Remove the transmission connector from 
bracket.
2) Drain the automatic transmission fluid.

CAUTION:
Do not drain ATF until it cools down.

3) Remove the oil pan.
4) Disconnect the connector from the control 
valve body.
5) Measure the resistance between low clutch 
duty solenoid connector and transmission 
ground.

Connector & terminal

(AT2) No. 2 — Transmission ground:

Is the resistance 2.0 — 6.0 

:

? Go to step 

8

.

Replace the con-
trol valve body. 
<Ref. to 4AT-58, 
Control Valve 
Body.>

8

CHECK HARNESS CONNECTOR BETWEEN 
TRANSMISSION AND LOW CLUTCH DUTY 
SOLENOID.

Measure the resistance of harness between low 
clutch duty solenoid and transmission connec-
tor.

Connector & terminal

(T4) No. 4 — (AT2) No. 2:

Is the resistance less than 1 

:

? Go to step 

9

.

Repair the open 
circuit of harness 
between low clutch 
duty solenoid and 
transmission con-
nector.

9

CHECK HARNESS CONNECTOR BETWEEN 
TRANSMISSION AND LOW CLUTCH DUTY 
SOLENOID.

Measure the resistance of harness between 
transmission connector and transmission 
ground.

Connector & terminal

(T4) No. 4 — Transmission ground:

Is the resistance 1 M

:

 or 

more?

Check the har-
nesses or connec-
tors between low 
clutch duty sole-
noid and transmis-
sion, and repair the 
defective part.

Repair the short 
circuit of harness 
between low clutch 
duty solenoid and 
transmission con-
nector.

Step

Check

Yes

No

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Samsung HF1000 User Manual preview
HF1000
Бренд: Samsung Страницы: 133
Jeep Liberty Quick Reference Manual preview
Liberty
Бренд: Jeep Страницы: 6
Vauxhall Ampera Owner'S Manual preview
Ampera
Бренд: Vauxhall Страницы: 199
HUSKY LINERS X-ACT CONTOUR 53491 Care And Use Instructions preview
X-ACT CONTOUR 53491
Бренд: HUSKY LINERS Страницы: 2
Volvo 30728293 Installation Instructions Manual preview
30728293
Бренд: Volvo Страницы: 19
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
FORM FIT 1303 Installation Instructions preview
1303
Бренд: FORM FIT Страницы: 2
Trailboss QTHD519L Fitting Instructions Manual preview
QTHD519L
Бренд: Trailboss Страницы: 8
Saab 32 025 888 Installation Instructions preview
32 025 888
Бренд: Saab Страницы: 3
Yakima StickUp Installation Instructions Manual preview
StickUp
Бренд: Yakima Страницы: 21
Xhorse VVDI User Manual preview
VVDI
Бренд: Xhorse Страницы: 48
Yutrax TX107 Operator'S Manual preview
TX107
Бренд: Yutrax Страницы: 8
Jaeger 21260514J Fitting Instructions Manual preview
21260514J
Бренд: Jaeger Страницы: 11
ATS 664-0030 Installation And Operating Manual preview
664-0030
Бренд: ATS Страницы: 12
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Бренд: Acura Страницы: 16
MMD 41240 Quick Manual preview
41240
Бренд: MMD Страницы: 3
Mazda 2006 MPV Quick Tips preview
2006 MPV
Бренд: Mazda Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды