manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

ME(H4SO)-45

V-belt

MECHANICAL

C: INSPECTION

1. FRONT SIDE BELT

CAUTION:
Check and adjust the front side belt tension so
that it is within the specified range. Using the
belt with a tension out of the specified range
may result in a fault such as the following:
• If the front side belt tension is higher, unex-
pected force is generated at the power steering
oil pump, generator and crankshaft bearing,
causing abnormal noise due to abnormal wear
of the bearing.
• If the front side belt tension is lower, the front
side belt and crank pulley slip, causing abnor-
mally high temperature on the crank pulley due
to frictional heat. If this condition repeatedly
occurs, the front side belt may abnormally
wear, causing abnormal noise, front side belt
damage or crank pulley damage.

1) Replace the front side belt, if crack, fraying or
wear is found.
2) Check the front side belt tension and adjust it if
necessary by changing the generator installing po-
sition.

Front side belt tension (with belt tension gauge):

When installing new parts

640 — 780 N (65 — 80 kgf, 144 — 175 lbf)

At inspection

490 — 640 N (50 — 65 kgf, 110 — 144 lbf)

Front side belt tension (without belt tension gauge):

When installing new parts

7 — 9 mm (0.276 — 0.354 in)

At inspection

9 — 11 mm (0.354 — 0.433 in)

2. REAR SIDE BELT

If cracks, fraying or wear is found, and when abnor-
mal noise is produced, replace the rear side belt.

NOTE:
Because the rear side belt is a stretch type belt, it is
not necessary to check deflection and tension.

(A) Front side belt

(B) Rear side belt

C/P Crank pulley

GEN Generator pulley

P/S Power steering oil pump pulley

A/C A/C compressor pulley

ME-03313

C/P

P/S

A/C

GEN

(A)

(B)

(A) Front side belt

(B) Rear side belt

(C) 98 N (10 kgf, 22 lbf)

C/P Crank pulley

GEN Generator pulley

P/S Power steering oil pump pulley

A/C A/C compressor pulley

ME-03314

(A)

(B)

GEN

C/P

A/C

P/S

(C)

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Dakota Digital VHX-37F Installation preview
VHX-37F
Бренд: Dakota Digital Страницы: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Бренд: Dakota Digital Страницы: 7
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Бренд: Ford Страницы: 2
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Бренд: Air Lift Страницы: 12
EZTRUNK PHANTOM JK Assembly Manual preview
PHANTOM JK
Бренд: EZTRUNK Страницы: 3
Mazda 2006 RX-8 Service Highlights preview
2006 RX-8
Бренд: Mazda Страницы: 122
Skoda Superb 2006 Owner'S Manual preview
Superb 2006
Бренд: Skoda Страницы: 281
Kia Picanto Manual preview
Picanto
Бренд: Kia Страницы: 680
travall TDG 1486 Fitting Instructions preview
TDG 1486
Бренд: travall Страницы: 4
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Бренд: Whelen Engineering Company Страницы: 2
Volvo M3602654 Installation Instructions Manual preview
M3602654
Бренд: Volvo Страницы: 10
Volvo 30795637 User Manual preview
30795637
Бренд: Volvo Страницы: 92
QA1 GS501 Installation Instructions preview
GS501
Бренд: QA1 Страницы: 3
Vauxhall 2013 Zafira Tourer Owner'S Manual preview
2013 Zafira Tourer
Бренд: Vauxhall Страницы: 289
Roadefend RDT401P Instruction Book preview
RDT401P
Бренд: Roadefend Страницы: 15
Mercedes-Benz W211 Manual preview
W211
Бренд: Mercedes-Benz Страницы: 27
PEUGEOT 5008 2017 Handbook preview
5008 2017
Бренд: PEUGEOT Страницы: 404
Yakima K1095 Instructions Manual preview
K1095
Бренд: Yakima Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды