manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

SC(H4SO)-20

Generator

STARTING/CHARGING SYSTEMS

E: INSPECTION

1. DIODE

CAUTION:
There is the possibility of damaging the diodes
if a mega-tester (used to measure high voltag-
es) or a similar measuring instrument is used.
Never use a mega tester or equivalent for this
test.

1) Check the positive diode
Check for continuity between the diode lead and
positive side heat sink. If resistance is 1 

:

 or less

only in the direction from the diode lead to the heat
sink, the positive diode is OK.

2) Check negative diode
Check for continuity between the negative side
heat sink and diode lead. If resistance is 1 

:

 or less

only in the direction from the heat sink to the diode
lead, the negative diode is OK.

2. ROTOR

1) Slip ring surface
Inspect the slip rings for contamination or any
roughness on the sliding surface. Repair the slip
ring surface using a lathe or sand paper.
2) Slip ring outer diameter
Measure the slip ring outer diameter. Replace the
rotor assembly if the slip ring is worn.

Slip ring outer diameter:

Standard

22.7 mm (0.894 in)

Limit

22.1 mm (0.870 in)

3) Continuity test
Using a circuit tester, check the resistance between
slip rings.
If the resistance is not within the standard, replace
the rotor assembly.

Specified resistance:

Approximately 1.8 — 2.2 

:

4) Insulation test
Check the continuity between slip ring and rotor
core or shaft. If the resistance is 1 

:

 or less, re-

place the rotor assembly because the rotor coil is
grounded.

5) Ball bearings (rear side)
Check the rear ball bearing. If there is any noise, or
the rotor does not rotate smoothly, replace the
bearings.

(A) Diode lead
(B) Heat sink (positive side)

(A) Diode lead

(B) Heat sink (negative side)

SC-00042

(B)

(A)

(A)

(B)

SC-00043

SC-00044

SC-00045

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Hama Pico Operating Instructions preview
Pico
Бренд: Hama Страницы: 2
Jabra TOUR Get Started preview
TOUR
Бренд: Jabra Страницы: 10
Yakima K1188 Instructions Manual preview
K1188
Бренд: Yakima Страницы: 12
JEHNERT SOUND DESIGN 65400 Assembly Instruction Manual preview
65400
Бренд: JEHNERT SOUND DESIGN Страницы: 8
Rainbow Experience Series Installation Manual preview
Experience Series
Бренд: Rainbow Страницы: 19
Yakima K1006 Instructions Manual preview
K1006
Бренд: Yakima Страницы: 12
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Бренд: Saleen Страницы: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Бренд: Buick Страницы: 5
Bestop WrapAround Windjammer Installation Instructions Manual preview
WrapAround Windjammer
Бренд: Bestop Страницы: 7
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Бренд: Waeco Страницы: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Бренд: Tusk Страницы: 2
Kargo Master 4A82T Installation Manual preview
4A82T
Бренд: Kargo Master Страницы: 6
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Бренд: Renault Страницы: 183
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Бренд: Dodge Страницы: 5
Edelbrock 65932 Installation Instructions preview
65932
Бренд: Edelbrock Страницы: 2
Buick Electra 225 1965 Service Manual preview
Electra 225 1965
Бренд: Buick Страницы: 914

Бренды по названию

Популярные бренды

Загрузить еще бренды