manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

DS-10

Propeller Shaft

DRIVE SHAFT SYSTEM

2. Propeller Shaft

A: REMOVAL

NOTE:
• Before removing propeller shaft, wrap metal
parts with a cloth or rubber material.
• In case of a EDJ type, wrap the metal parts at the
rubber boot of center EDJ with a cloth or rubber
material before removing propeller shaft, as shown
in the figure. The rubber boot may be damaged due
to interference with adjacent metal parts while
bending the EDJ during removal.

1) Disconnect the ground cable from the battery.
2) Shift the select lever or gear shift lever to neutral.
3) Release the parking brake.
4) Lift up the vehicle.
5) Remove the center exhaust pipe.
6) Remove the rear exhaust pipe and muffler.
7) Remove the heat shield cover.

8) Make alignment marks on the flange yoke and
rear differential before removal.

9) Remove the three bolts holding the propeller
shaft to the rear differential.
10) Remove the remaining bolt.
11) Remove the two bolts which hold center bear-
ing to vehicle body.

12) Remove the propeller shaft from transmission.

CAUTION:
• Be careful not to damage oil seals and con-
tact surface of the sleeve yoke.
• Cover the center exhaust pipe with a cloth to
keep off any ATF or oil spilled from transmis-
sion when removing propeller shaft.

NOTE:
Use a container to catch ATF or oil flowing from
propeller shaft.

(A) Heat shield cover

DS-00239

DS-00230

(A)

(A) Alignment mark

DS-00028

(A)

DS-00141

DS-00030

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

AA Products X31 Instruction Manual preview
X31
Бренд: AA Products Страницы: 6
LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Бренд: Safe Fleet Страницы: 12
BGS technic 40108 Manual preview
40108
Бренд: BGS technic Страницы: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Бренд: Oldsmobile Страницы: 344
ABL eMH3 Installation Manual preview
eMH3
Бренд: ABL Страницы: 66
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Бренд: Honda Страницы: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Бренд: Pro-gard Страницы: 4
Nav TV Ford 4” UNI-CAM Manual preview
Ford 4” UNI-CAM
Бренд: Nav TV Страницы: 6
Saab 2007 9-3 Remote Starter Owner'S Manual preview
2007 9-3 Remote Starter
Бренд: Saab Страницы: 304
Buick 2015 LaCrosse Getting To Know Manual preview
2015 LaCrosse
Бренд: Buick Страницы: 20
Pacbrake HP10098 Installation Manual preview
HP10098
Бренд: Pacbrake Страницы: 6
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Бренд: Ecco Страницы: 24
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Бренд: Columbia Страницы: 14
ADS FlashLogic FLC-FORS-FO1B-FLRSFO1-EN Install Manual preview
FlashLogic FLC-FORS-FO1B-FLRSFO1-EN
Бренд: ADS Страницы: 25
Honda 2007 Fit User Information preview
2007 Fit
Бренд: Honda Страницы: 24
Mobridge DA-G2 MOST150 Manual preview
DA-G2 MOST150
Бренд: Mobridge Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды