manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

FS-25

Front Crossmember

FRONT SUSPENSION

8. Front Crossmember

A: REMOVAL

1) Lift up the vehicle, and then remove the front
wheels.
2) Remove the front exhaust pipe.
3) Remove the front crossmember support plate.
<Ref. to FS-15, REMOVAL, Front Crossmember
Support Plate.>
4) Remove the front stabilizer. <Ref. to FS-16, RE-
MOVAL, Front Stabilizer.>
5) Disconnect the tie-rod end from housing.
6) Remove the front arm. <Ref. to FS-19, REMOV-
AL, Front Arm.>
7) Remove the nuts attaching the engine mount
cushion rubber to crossmember.

8) Remove the steering universal joint.
9) Disconnect the power steering hose from steer-
ing gearbox.
10) Lift the engine approx. 10 mm (0.39 in) using a
chain block.
11) Support the crossmember with a jack, remove
the bolts securing crossmember to body, and then
gradually lower the crossmember with steering
gearbox as a unit.

CAUTION:
When removing the crossmember downward,
be careful that the tie-rod end does not interfere
with drive shaft boot.

B: INSTALLATION

1) Install in the reverse order of removal.

CAUTION:
• Use a new bolt and self-locking nut. For parts
which are not reusable, refer to COMPONENT.
<Ref. to FS-3, COMPONENT, General Descrip-
tion.>
• Always tighten the bushing in the state where
the vehicle is at curb weight and the wheels are
in full contact with the ground.

Tightening torque:

Crossmember to Body:

95 N·m (9.7 kgf-m, 70.1 ft-lb)

Engine mounting to Crossmember:

85 N·m (8.7 kgf-m, 62.7 ft-lb)

Front arm to Crossmember:

95 N·m (9.7 kgf-m, 70.1 ft-lb)

Front arm to Support plate:

110 N·m (11.2 kgf-m, 81.1 ft-lb)

Support plate body:

150 N·m (15.3 kgf-m, 110.6 ft-lb)

Tie-rod end to Housing:

27 N·m (2.8 kgf-m, 19.9 ft-lb)

After tightening to the specified torque, tighten the
castle nut further but within 60° until the hole in the
ball stud is aligned with a slot in castle nut

Tightening torque:

Universal joint:

24 N·m (2.4 kgf-m, 17.7 ft-lb)

Stabilizer bracket:

25 N·m (2.5 kgf-m, 18.4 ft-lb)

Stabilizer link:

45 N·m (4.6 kgf-m, 33.2 ft-lb)

Power steering hose to Steering gearbox:

15 N·m (1.5 kgf-m, 11.1 ft-lb)

2) Purge air from the power steering system.
3) Inspect the wheel alignment and adjust if neces-
sary.

C: INSPECTION

Check the crossmember for damage or cracks, and
correct or replace if defective.

FS-00118

FS-00119

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Calira 811 Manual preview
811
Бренд: Calira Страницы: 14
Quadratec QR3 Installation Manual preview
QR3
Бренд: Quadratec Страницы: 8
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Бренд: Ultra-tow Страницы: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Бренд: Mercedes-Benz Страницы: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Бренд: Menabo Страницы: 8
Camtree G-51 Instruction Manual preview
G-51
Бренд: Camtree Страницы: 5
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Бренд: Mazdaspeed Страницы: 8
SnapPad EQ Round Installation Instructions preview
EQ Round
Бренд: SnapPad Страницы: 5
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Бренд: Wagan Страницы: 20
Whipple TOMAHAWK V1 Instruction Manual preview
TOMAHAWK V1
Бренд: Whipple Страницы: 3
Parrot Parrot MKi + ParrotCK3100 range LOGAN Installation Manual preview
Parrot MKi + ParrotCK3100 range LOGAN
Бренд: Parrot Страницы: 10
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Бренд: Rugged Ridge Страницы: 3
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Бренд: Vauxhall Страницы: 245
Metra Electronics 99-5026 Installation Instructions Manual preview
99-5026
Бренд: Metra Electronics Страницы: 20
Mazda 3 Facelift 2006 Training Manual preview
3 Facelift 2006
Бренд: Mazda Страницы: 94
Volvo 30795637 User Manual preview
30795637
Бренд: Volvo Страницы: 92
Menabo ANTARES KIT+1 Assembly & Instruction Manual preview
ANTARES KIT+1
Бренд: Menabo Страницы: 8
Seat Arona 2018 Owner'S Manual preview
Arona 2018
Бренд: Seat Страницы: 372

Бренды по названию

Популярные бренды

Загрузить еще бренды