manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

5MT-80

General Diagnostic Table

MANUAL TRANSMISSION AND DIFFERENTIAL

20.General Diagnostic Table

A: INSPECTION

1. MANUAL TRANSMISSION

Symptom

Possible cause

Corrective action

1. Gears are difficult to intermesh.

NOTE:
The cause for difficulty in shifting gears 
can be classified into two kinds: One is a 
defective gear shift system and the other 
is defective transmission. However, if the 
operation is heavy and engagement of the 
gears is difficult, a defective clutch disen-
gagement may also be responsible. 
Check whether the clutch is correctly 
functioning, before checking the gear shift 
system and transmission.

(a) Worn, damaged or burred chamfer at 
internal spline of the sleeve and reverse 
driven gear

Replace.

(b) Worn, damaged or burred chamfer of 
gear spline

Replace.

(c) Worn or scratched bushings

Replace.

(d) Incorrect contact or wear between 
synchronizer ring and gear cone

Correct or replace.

2. Gear slip-out
• Gear slips out when coasting on rough 
road.
• Gear slips out during acceleration.

(a) Defective pitching stopper adjustment

Adjust.

(b) Loose engine mounting bolts

Tighten or replace.

(c) Worn fork shifter, broken shifter fork 
rail spring

Replace.

(d) Worn or damaged ball bearing

Replace.

(e) Excessive clearance between splines 
of synchronizer hub and synchronizer 
sleeve

Replace.

(f) Worn tooth step of synchronizer hub 
(caused by slip-out of 3rd gear)

Replace.

(g) Worn 1st driven gear and driven shaft

Replace.

(h) Worn 2nd driven gear and bushing

Replace.

(i) Worn 3rd drive gear and needle bear-
ing

Replace.

(j) Worn 4th drive gear and needle bear-
ing

Replace.

(k) Worn reverse idler gear and bushing

Replace.

3. Noise emitted from transmission

NOTE:
If a noise is heard when the vehicle is 
parked with its engine idling and if a noise 
ceases when the clutch is disengaged, it 
may be considered that the noise is com-
ing from the transmission.

(a) Insufficient or improper lubrication

Lubricate with specified oil or replace.

(b) Worn or damaged gears and bearings

NOTE:
If the trouble is only wear of the gear teeth 
surfaces, only a high whirring noise will 
occur at high speeds, but if any part is bro-
ken, rhythmical clicking sounds will be 
heard even at low speeds.

Replace.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Бренд: Farad Страницы: 8
Toyota YARIS LIFTBACK 2009 Quick Reference Manual preview
YARIS LIFTBACK 2009
Бренд: Toyota Страницы: 13
Westfalia 316 145 Manual preview
316 145
Бренд: Westfalia Страницы: 71
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Бренд: Kolpin Outdoors Страницы: 6
Schartec CR 4 Manual preview
CR 4
Бренд: Schartec Страницы: 2
K&M MILSCO KIT# C746700 Installation Manual preview
MILSCO KIT# C746700
Бренд: K&M Страницы: 2
Car-Interface CI-RL4-NAC12 Manual preview
CI-RL4-NAC12
Бренд: Car-Interface Страницы: 25
Thule 2 Bike Carrier 977 Instructions Manual preview
2 Bike Carrier 977
Бренд: Thule Страницы: 6
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Бренд: Cadillac Страницы: 522
RBO RBO4038 Product Manual preview
RBO4038
Бренд: RBO Страницы: 15
Radical Sportscars SR 3 SL Owner'S Handbook Manual preview
SR 3 SL
Бренд: Radical Sportscars Страницы: 44
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Бренд: Honda Страницы: 124
Gator GRM430EM User Manual preview
GRM430EM
Бренд: Gator Страницы: 6
Discount Car Stereo A2DIY-MBR Quick Start Bluetooth Installation Manual preview
A2DIY-MBR
Бренд: Discount Car Stereo Страницы: 8
Mercedes-Benz W211 Manual preview
W211
Бренд: Mercedes-Benz Страницы: 27
Yakima K1198 Instructions Manual preview
K1198
Бренд: Yakima Страницы: 10
Connects2 CTQIAU03 Installation & User Manual preview
CTQIAU03
Бренд: Connects2 Страницы: 2
ULTIMATE SPEED 274817 Instructions For Use And Safety Manuallines preview
274817
Бренд: ULTIMATE SPEED Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды