manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4DOTC)(diag)-316

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

13

CHECK MASS AIR FLOW AND INTAKE AIR 
TEMPERATURE SENSOR.

1) Start the engine and warm up engine until 
coolant temperature is higher than 75°C 
(167°F).
2) For AT models, set the select lever to “P” 
range or “N” range, and for MT models, place 
the shift lever in the neutral position.
3) Turn the A/C switch to OFF.
4) Turn all the accessory switches to OFF.
5) Read the data of the mass air flow and 
intake air temperature sensor signal using Sub-
aru Select Monitor or general scan tool.
NOTE:
• Subaru Select Monitor
For detailed operation procedures, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4DOTC)(diag)-34, Subaru Select Moni-
tor.>
• General scan tool
For detailed operation procedures, refer to the
general scan tool operation manual.

Is the measured value 2.0 — 
5.0 g/s (0.26 — 0.66 lb/s) ?

Go to step 

14

.

Replace the mass 
air flow and intake 
air temperature 
sensor. <Ref. to 
FU(H4DOTC)-39, 
Mass Air Flow and 
Intake Air Temper-
ature Sensor.>

14

CHECK MASS AIR FLOW AND INTAKE AIR 
TEMPERATURE SENSOR.

1) Start the engine and warm up engine until 
coolant temperature is higher than 75°C 
(167°F).
2) For AT models, set the select lever to “P” 
range or “N” range, and for MT models, place 
the shift lever in the neutral position.
3) Turn the A/C switch to OFF.
4) Turn all the accessory switches to OFF.
5) Open the front hood.
6) Measure the ambient temperature.
7) Read the data of the mass air flow and 
intake air temperature sensor signal using Sub-
aru Select Monitor or general scan tool.
NOTE:
• Subaru Select Monitor
For detailed operation procedures, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4DOTC)(diag)-34, Subaru Select Moni-
tor.>
• General scan tool
For detailed operation procedures, refer to the
general scan tool operation manual.

Subtract ambient temperature 
from intake air temperature. Is 
the obtained value –10 — 50°C 
(–18 — 90°F)?

Go to step 

15

.

Check the mass air 
flow and intake air 
temperature sen-
sor. <Ref. to 
FU(H4DOTC)-39, 
Mass Air Flow and 
Intake Air Temper-
ature Sensor.>

Step

Check

Yes

No

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

CAMPARK R10 Manual preview
R10
Бренд: CAMPARK Страницы: 20
Camcar 40104 Mounting Instructions preview
40104
Бренд: Camcar Страницы: 6
Kargo Master 40131 Installation Manual preview
40131
Бренд: Kargo Master Страницы: 5
Maserati Gransport Owner'S Manual preview
Gransport
Бренд: Maserati Страницы: 210
OnStar liveon Owner'S Manual preview
liveon
Бренд: OnStar Страницы: 22
Quadratec 12057.0261 Installation Manual preview
12057.0261
Бренд: Quadratec Страницы: 12
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Бренд: Advanced Diagnostics Страницы: 10
Bilstein E4-WM5-Y479A00 Mounting Instruction preview
E4-WM5-Y479A00
Бренд: Bilstein Страницы: 7
Volvo XC70 - ANNEXE 808 Quick Manual preview
XC70 - ANNEXE 808
Бренд: Volvo Страницы: 8
Brodit Getac T800 Quick Start Manual preview
Getac T800
Бренд: Brodit Страницы: 2
Saturn 2009 OUTLOOK Owner'S Manual preview
2009 OUTLOOK
Бренд: Saturn Страницы: 432
Xforce PR-104 User Manual preview
PR-104
Бренд: Xforce Страницы: 11
Buick Riviera 1967 Owner'S Manual preview
Riviera 1967
Бренд: Buick Страницы: 58
Lexus IS220d 2011 Manual preview
IS220d 2011
Бренд: Lexus Страницы: 609
Haltech Platinum Pro Plug-in Quick Start Manual preview
Platinum Pro Plug-in
Бренд: Haltech Страницы: 20
Monster iCarPlay Direct Connect 2000 User Manual & Warranty Information preview
iCarPlay Direct Connect 2000
Бренд: Monster Страницы: 66
Honda 2012 CR-V Owner'S Manual preview
2012 CR-V
Бренд: Honda Страницы: 384

Бренды по названию

Популярные бренды

Загрузить еще бренды