manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

SL-22

Keyless Entry System

SECURITY AND LOCKS

7. CHECK ROOM LIGHT OPERATION

8. CHECK HAZARD LIGHT OPERATION

Step

Check

Yes

No

1

CHECK ROOM LIGHT OPERATION.

Make sure the room light illuminates when the 
room light switch is ON, and goes off when the 
switch is OFF.

Does the room light illuminate 
or go off?

Go to step 

2

.

Check the harness 
between the fuse 
and main fuse box 
and room light.

2

CHECK ROOM LIGHT OPERATION.

1) Turn the room light switch to the “DOOR” 
position.
2) Open/close any door (other than trunk).

Does the room light illuminate 

œ

 go off (including off delay) 

when the door is opened and 
closed?

Go to step 

3

.

Go to step 

4

.

3

CHECK KEYLESS ENTRY OPERATION.

Press the LOCK/UNLOCK button of the keyless 
transmitter.

Does it operate properly?

Replace the body 
integrated unit. 
<Ref. to SL-50, 
Body Integrated 
Unit.>

Check the bulb or 
room light assem-
bly, and replace if 
necessary.

4

CHECK HARNESS.

1) Disconnect the body integrated unit harness 
connector and room light harness connector.
2) Measure the resistance between harness 
connector terminals.

Connector & terminal

(B279) No. 5 — (R52) No. 2:

Is the resistance less than 10 

:

? Go to step 

5

.

Repair or replace 
the harness.

5

CHECK HARNESS.

Measure the voltage between room light har-
ness connector terminal and chassis ground.

Connector & terminal

(R52) No. 3 (+) — Chassis ground (–):

Is the voltage 10 V or more?

Replace the body 
integrated unit. 
<Ref. to SL-50, 
Body Integrated 
Unit.>

Repair or replace 
the harness.

Step

Check

Yes

No

1

CHECK HAZARD LIGHT OPERATION.

Make sure the hazard light blinks when hazard 
switch is turned to ON.

Does the hazard light blink?

Go to step 

2

.

Check the hazard 
light circuit.

2

CHECK OUTPUT TO HAZARD LIGHT.

1) Turn the ignition switch to OFF.
2) Disconnect the key warning switch harness 
connector.
3) Prepare the Subaru Select Monitor kit.
4) Turn the ignition switch to ON (engine OFF) 
and run the “PC application for Subaru Select 
Monitor”.
5) On «System Selection Menu» display, 
select {Integ. unit mode}.
6) Select {ECM customizing}.
7) Check {Hazard answer-back setup}, and 
then switch to ON setting if necessary.
8) Select the {Current Data Display & Save}.
9) Remove the key from ignition switch.
10) Select the {Hazard Output}.

Is output signal present when 
operating the transmitter 
LOCK/UNLOCK button?

Go to step 

3

.

Check body inte-
grated unit. <Ref. 
to LAN(diag)-2, 
Basic Diagnostic 
Procedure.>

3

CHECK CIRCUIT OF HAZARD LIGHT.

1) Disconnect the harness connector of body 
integrated unit.
2) Disconnect the turn signal and hazard unit 
harness connector.
3) Measure the resistance between harness 
connector terminals.

Connector & terminal

(B281) No. 22 — (B32) No. 8:

Is the resistance less than 10 

:

? Check body inte-

grated unit. <Ref. 
to LAN(diag)-2, 
Basic Diagnostic 
Procedure.>

Repair or replace 
the harness.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Warrior Products 10936 Installation Instructions preview
10936
Бренд: Warrior Products Страницы: 3
Honda HRM3000 User Manual preview
HRM3000
Бренд: Honda Страницы: 73
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Saab 32 025 888 Installation Instructions preview
32 025 888
Бренд: Saab Страницы: 3
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Hyundai Santa Fe 2019 Getting Started Manual preview
Santa Fe 2019
Бренд: Hyundai Страницы: 18
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
KEKO K162 Installation Instructions Manual preview
K162
Бренд: KEKO Страницы: 13
Road Armor Stealth 4191F Series Install Instructions preview
Stealth 4191F Series
Бренд: Road Armor Страницы: 5
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Бренд: Subaru Страницы: 19
Dodge 2010 Challenger SRT Owner'S Manual preview
2010 Challenger SRT
Бренд: Dodge Страницы: 444
Edelbrock 2917 Nstallation Instructions preview
2917 Nstallation
Бренд: Edelbrock Страницы: 1
Alfa Romeo Giulietta 2.0 JTDM Manual preview
Giulietta 2.0 JTDM
Бренд: Alfa Romeo Страницы: 14
Curt Manufacturing 58963 Installation Manual preview
58963
Бренд: Curt Manufacturing Страницы: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Бренд: Whispbar Страницы: 112
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Бренд: IOGear Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды