manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

SL-28

Security System

SECURITY AND LOCKS

NOTE:
Check the function settings of the body integrated unit if any of the following symptoms appear. <Ref. to
LAN(diag)-2, Basic Diagnostic Procedure.>
• The horn does not sound even when the security alarm is triggered and operating. As a cause, it is possi-
ble that the siren ON/OFF setting is set to ON in the customization function.
• The horn sounds when setting the security to ON (Monitoring condition) using the keyless transmitter. As
a cause, it is possible that the impact sensor present (ON) / not present (OFF) setting is set to ON in the cus-
tomization function though there is no impact sensor.

2. CHECK SECURITY SYSTEM CONDITION MEMORY

1) Pull out the key from the ignition switch, or turn the ignition to OFF.
2) Close all the doors, trunk lid and rear gate.
3) Open the front hood.
4) Press the LOCK button of the keyless transmitter.

NOTE:
Wait until the security indicator light blinks twice within 0.5 seconds at 2 second intervals.
If the 30 second monitoring lag has been set, wait 30 seconds.
5) Disconnect the ground cable from the battery.
6) Connect the ground cable to the battery.
7) Check that the security indicator light blinks twice within 0.5 seconds at 2 second intervals. When it does
not blink, replace the body integrated unit.

3. SECURITY SYSTEM ON/OFF SETTING

1) Close all doors, trunk lid and rear gate, and sit down on the driver seat. Press the UNLOCK button of the
keyless transmitter.
2) Turn the ignition switch to ON.
3) Push the centralized door lock switch down and open the driver’s side door at the same time, and hold in
this condition for 10 seconds.
4) If the security system is ON, it will turn OFF. If OFF, it will turn ON.

4. CHECK DOOR SWITCH

For operation procedure, refer to the door switch inspection of the keyless entry system. <Ref. to SL-19,
CHECK DOOR SWITCH, INSPECTION, Keyless Entry System.>

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Honda HRM3000 User Manual preview
HRM3000
Бренд: Honda Страницы: 73
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Бренд: Roadmaster Страницы: 12
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Бренд: SuperATV Страницы: 3
U.S. General 95904 Operating Instructions preview
95904
Бренд: U.S. General Страницы: 4
TATA Motors Sumo Victa EX Owner'S Manual & Service Book preview
Sumo Victa EX
Бренд: TATA Motors Страницы: 92
Skoda Fabia II 2007 Workshop Manual preview
Fabia II 2007
Бренд: Skoda Страницы: 165
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Бренд: Ecco Страницы: 24
Westin 32-1660 Instructions preview
32-1660
Бренд: Westin Страницы: 3
SMART EQ forfour 2018 Owner'S Manual preview
EQ forfour 2018
Бренд: SMART Страницы: 224
Federal Signal Corporation Cuda TriOptic 351014F Series Instruction Sheet preview
Cuda TriOptic 351014F Series
Бренд: Federal Signal Corporation Страницы: 4
Kia Magentis 2002 Owner'S Manual preview
Magentis 2002
Бренд: Kia Страницы: 216
Metra Electronics 99-6510 User Manual preview
99-6510
Бренд: Metra Electronics Страницы: 17
Yakima Safety Pole Quick Start Manual preview
Safety Pole
Бренд: Yakima Страницы: 4
Volvo XC40 RECHARGE Retailer Pairing Manual preview
XC40 RECHARGE
Бренд: Volvo Страницы: 5
Lincoln 2011 navigator Manual preview
2011 navigator
Бренд: Lincoln Страницы: 370
Audiovox Rear Observation System Package RVMPKG2 Installation Manual preview
Rear Observation System Package RVMPKG2
Бренд: Audiovox Страницы: 15
Brink 4602 Fitting Instructions Manual preview
4602
Бренд: Brink Страницы: 12
Mercedes-Benz SLK 2014 Owner'S Manual preview
SLK 2014
Бренд: Mercedes-Benz Страницы: 357

Бренды по названию

Популярные бренды

Загрузить еще бренды