manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4DOTC)(diag)-325

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK ELECTRONIC THROTTLE CON-
TROL RELAY.

1) Turn the ignition switch to OFF.
2) Remove the electronic throttle control relay.
3) Connect the battery to terminals No. 31 and 
No. 32 of electronic throttle control relay.
4) Measure the resistance between electronic 
throttle control relay terminals.

Terminals

No. 29 — No. 30:

Is the resistance less than 1 

:

? Go to step 

2

.

Replace the elec-
tronic throttle con-
trol relay. <Ref. to 
FU(H4DOTC)-57, 
Electronic Throttle 
Control Relay.>

2

CHECK POWER SUPPLY OF ELECTRONIC 
THROTTLE CONTROL RELAY.

Measure the voltage between electronic throttle 
control relay connector and chassis ground.

Connector & terminal

(B220) No. 29 (+) — Chassis ground (–):

Is the voltage 10 V or more?

Go to step 

3

.

Repair the open or 
ground short circuit 
of power supply 
circuit.

3

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL RE-
LAY CONNECTOR.

1) Disconnect the connectors from ECM.
2) Turn the ignition switch to ON.
3) Measure the voltage between electronic 
throttle control relay connector and chassis 
ground.

Connector & terminal

(B220) No. 32 (+) — Chassis ground (–):

Is the voltage 10 V or more?

Repair the short 
circuit to power in 
the harness 
between ECM and 
electronic throttle 
control relay con-
nector.

Go to step 

4

.

4

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL RE-
LAY CONNECTOR.

1) Turn the ignition switch to OFF.
2) Measure the resistance between electronic 
throttle control relay connector and chassis 
ground.

Connector & terminal

(B220) No. 32 — Chassis ground:
(B220) No. 30 — Chassis ground:

Is the resistance 1 M

:

 or 

more?

Go to step 

5

.

Repair the short 
circuit in harness 
to ground between 
ECM and elec-
tronic throttle con-
trol relay 
connector.

5

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL RE-
LAY CONNECTOR.

Measure the resistance between ECM and 
electronic throttle control relay connector.

Connector & terminal

(B136) No. 21 — (B220) No. 32:
(B136) No. 1 — (B220) No. 30:

Is the resistance less than 1 

:

? Repair the poor 

contact of ECM 
connector.

Repair the open 
circuit in harness 
between ECM and 
electronic throttle 
control relay con-
nector.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Acdeos AXS FL Installation Instruction preview
AXS FL
Бренд: Acdeos Страницы: 7
PAC SWI-RC Installation Instructions preview
SWI-RC
Бренд: PAC Страницы: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Бренд: PAC Страницы: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Бренд: PAC Страницы: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Бренд: PAC Страницы: 5
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Бренд: Ford Страницы: 2
APEXi V-AFC II Instruction Manual preview
V-AFC II
Бренд: APEXi Страницы: 18
Prorack K519 Fitting Instructions For Basic Carrier preview
K519
Бренд: Prorack Страницы: 15
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
Whispbar K561W Fitting Instructions Manual preview
K561W
Бренд: Whispbar Страницы: 15
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Бренд: Cadillac Страницы: 34
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Бренд: TATA Motors Страницы: 136
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Бренд: Lit Lightz Страницы: 3
Prorack K374 Manual preview
K374
Бренд: Prorack Страницы: 14
Scosche HUD580GC Manual preview
HUD580GC
Бренд: Scosche Страницы: 12
RAM TRUCK 2500 2017 Owner'S Manual Supplement preview
TRUCK 2500 2017
Бренд: RAM Страницы: 33
Kargo Master PRO-II KS Assembly Instructions Manual preview
PRO-II KS
Бренд: Kargo Master Страницы: 8
Honda 1993 Civic Coupe Owner'S Manual preview
1993 Civic Coupe
Бренд: Honda Страницы: 201

Бренды по названию

Популярные бренды

Загрузить еще бренды