Kobelco SK35SR-6 Скачать руководство пользователя страница 81

Страница: 81 / 296

This lever is used to adjust the engine speed

(output).

A: L (Low idle)

The lever is in the L position.

(The speed drops.)

B: S (S mode)

The lever is in the "S" position.

S mode focuses on the low fuel consumption

operation.

C: H (High idle)

The position where the lever is fully pulled

backward.

From the S mode position, pull the lever to

the right and then backward.

(The speed is maximized.)

The dozer can be operated by using the dozer

(1)control lever on the right side of the

operator's seat.

Dozer control lever (1) returns to

the neutral position if it is released and the

dozer can be kept at the same position at that

time.

Operation

Movement

Push the lever (A)

Dozer blade down

Pull the lever (B)

Dozer blade up

Neutral (C)

Hold

２

2.5.5

ENGINE THROTTLE LEVER

2.5.6

DOZER CONTROL LEVER

Dozer Operation

［

2. MACHINE FAMILIARIZATION

］

2-17

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды