Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 223 / 296

５

5.1

TRANSPORTATION OF HYDRAULIC EXCAVATOR

5.1.1

PREPARATION OF TRANSPORTATION

・

When transporting the machine with a trailer, etc., consider the width, height, length and mass with

the machine loaded. The transportation mass and dimension vary depending on the type of shoe

and the specifications of the attachment.

Refer to masses and dimensions described in "SPECIFICATIONS" in this manual to select the

proper transportation method.

・

Perform a previous inspection on the route such as limitations on width, height and mass (weight)

of vehicles and traffic regulations, etc.

・

Obtain any required permits from related government agencies for machine transportation.

［

5. TRANSPORTATION

］

5-3

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды