Kobelco SK35SR-6 Скачать руководство пользователя страница 171

Страница: 171 / 296

４

Prohibited use of the rubber track shoe can easily cause detachment of core metals.

See "HANDLING OF RUBBER TRACK SHOE (STANDARD)" in Chapter 3 to understand the

prohibitions on use of the rubber track shoe.

4.11.6

REPLACING RUBBER TRACK SHOE

Perform the work in pairs and the operator should operate the machine according to signals from the

other worker. The replacement of rubber track shoe is performed after raising up the machine.

It is

dangerous for the machine to fall unintentionally when replacing it. Do not move anything other than

the rubber track shoe to be replaced during the replacement work.

Grease cylinder is under high pressure. It is dangerous to loosen the grease nipple rapidly because

grease will splash. Loosen the grease nipple gradually with your face kept away from around the

grease nipple. The grease nipple can pop out due to the inner high pressure. Loosen it gradually

within one turn.

Make sure that the grease inside the grease cylinder is completely drained and then turn the

sprocket before removing the rubber track shoe.

It is very dangerous to splash the grease in other than the procedure described in "Removing

Rubber Track Shoe" in the next page. Contact KOBELCO authorized dealer/distributor for repair if the

rubber track shoe is not loosened.

Wash to remove any sand and soil around the tracks before replacement, inspection and adjustment.

［

4. INSPECTION AND MAINTENANCE

］

4-29

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды