Kobelco SK35SR-6 Скачать руководство пользователя страница 54

Страница: 54 / 296

If unauthorized personnel start the engine or

touch control levers without care during the

inspection and maintenance, it may cause

severe injury. Put the tags "DO NOT START

ENGINE!","DO NOT OPERATE" and "UNDER

INSPECTION/MAINTENANCE" on noticeable

places or where people can easily notice such

as around the operator's seat before

performing the inspection and maintenance. If

necessary, display tags around the machine.

1.8

PRECAUTIONS OF INSPECTION & MAINTENANCE

1.8.1

BEFORE INSPECTION & MAINTENANCE

READ CAREFULLY OPERATION/MAINTENANCE PROCEDURES

Improper maintenance may cause not only personal injury (being caught or burned) but also damage

to the machine.

Fully read and understand the maintenance procedures (preparation for safety work, tools,

qualifications, important parts, designation of the supervisor and wearing of the protective gears, etc.)

described in this manual before inspecting and maintaining the machine. And then safely and carefully

perform the inspection and maintenance.

CONFIRM THE JOB PROCEDURES

Confirm all working procedures before starting work to prevent accidents caused by lack of the

understanding of procedures. If the signal person is placed, fully confirm the signal person and the

signals.

ORGANIZE AND CLEAN UP THE WORKING SITE

Inspecting and maintaining the machine at a messy working site may cause personnel to fall down or

personal injury by debris.

Clear of obstacles, grease, oil, paint, debris, etc., from the working site and put things in order to

clean up the area for safety work.

PUT THE TAGS "DO NOT START ENGINE!", "DO NOT OPERATE" AND "UNDER
INSPECTION/MAINTENANCE"

USE PROPER TOOLS

Use of damaged or deformed tools for the purpose other than its original intention may cause personal

injury. Use properly calibrated and maintained tools.

［

1. SAFETY PRECAUTIONS

］

1-36

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды