Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 202 / 296

Park the machine on the level and firm

ground, extend the bucket cylinder, retract

the arm cylinder, lower the bucket to the

ground, and place the dozer on the

ground as shown to the right figure, and

then stop the engine.

Open the right side cover and support it

with the stay.

Press the rubber cap of the breather on

the top of the hydraulic oil tank several

times (5 - 7 times) to release the internal

pressure of the hydraulic oil tank.

Remove breather cap (1), and then

remove nut (2).

Turn cover (3) in the counterclockwise

direction, remove the cover, and then

remove element (4).

Install new element (4) and install cover (3)

along the groove.

Be sure to prevent water and dirt from

entering the air intake and exhaust ports

between cover (3) and body (5).

Attach cover (3), and then attach nut (2).

Attach breather cap (1).

10. Remove the stay and return the right side

cover to the specified position.

4.16.2

REPLACING AIR BREATHER ELEMENT

Immediately after operation, the oil is hot and it may result in burns. Wait until the oil temperature

cools down before attempting to change the element.

To avoid the breakage of bolts, do not over-tighten nut (2).

Tightening Torque: 10 to 14 N

･

m (7.3 to 10.3 lbf

･

ft)

To keep the hydraulic oil clean and to extend the service life of hydraulic components, replace the

filter element at regular intervals.

Every 1000 hours replacement is just a guideline. If the machine is operated in very dusty conditions,

replace the oil filter earlier than the specified period.

［

4. INSPECTION AND MAINTENANCE

］

4-60

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды