Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 86 / 296

Check that the seat belt is not twisted,

and insert it into buckle until it clicks.

Adjust the seat belt to remove excess slack.

・

To unfasten the seat belt, pull "a" of the

buckle.

2.8

HANDLING OF SEAT BELT

INSTALLATION OF SEAT BELT

Install the seat belt properly or the fundamental performance may not be achieved.

Make sure that there is no abnormality on the belt attaching bracket and bolts before fastening the

seat belt.

Check attaching bolts which are used to secure the belt to the seat for loosening and tighten loose

bolts again.

Change the seat belt every three years, even if there is no abnormality in the appearance. The

manufacturing date is woven into the back side of the belt.

Do not fail to fasten the seat belt during operation.

2.8.1

HOW TO FASTEN SEAT BELT

2.8.2

HOW TO UNFASTEN SEAT BELT

［

2. MACHINE FAMILIARIZATION

］

2-22

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды