Kobelco SK35SR-6 Скачать руководство пользователя страница 58

Страница: 58 / 296

・

A flying metal piece may cause severe

injury when hammering a hard metal part

such as pin, edge, tooth and bearing. Wear

protective gears such as protective

glasses, gloves, hard hat and protective

shoes to avoid injury.

・

When hammering a pin, tooth or other, a

flying metal piece or others may cause

injury. Confirm no one is around the

working site before hammering.

・

Do not heat the section close to the tube

and hose contained pressurized oil or

other combustible materials by welding,

soldering and torch.

・

If the pressurized tube and hose is heated

directly, they may be suddenly cut. When

carrying out the welding and soldering

works, cover the tube, hose and other

combustible materials with fire-proofed

covers.

・

Personal injury or failures of the machine

caused by unspecified modification voids

our liability for the machine.

・

Consult KOBELCO authorized

dealer/distributor for any modification to the

machine beforehand.

PAYING ATTENTION TO BROKEN PIECES WHEN HAMMERING

When hammering, popping up pins or flying metal chips may cause severe injury. Strictly follow the

instructions below.

1.8.3

PROHIBITED IN INSPECTION & MAINTENANCE

DO NOT HEAT NEAR PRESSURIZED HYDRAULIC EQUIPMENT NOR PIPING

Do not heat the sections close to the tubes and hoses with pressurized oil when welding, soldering

and using a torch. It may cause generation of combustible steam or gas and result in a fire or severe

burns.

DO NOT HEAT PIPING CONTAINING COMBUSTIBLE OIL

・

Do not employ gas cutting for the pipes and tubes containing combustible oil.

・

Wash combustible oil completely with non-combustible solvent before welding and gas cutting.

MODIFICATION IS PROHIBITED

［

1. SAFETY PRECAUTIONS

］

1-40

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды