Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 57 / 296

Accident may occur without support. When

lifting up the machine for inspection of the

undercarriage, operate the boom and arm to

form an angle of 90 to 110 degrees between

them, and lower the bucket to let its bottom

touch the ground to lift the machine body up,

and support the machine with safety strut (1)

and safety block (2).

Grease cylinder is under high pressure. It is

dangerous to loosen the grease nipple rapidly

because grease will splash. Loosen the grease

fitting within one turn while relieving pressure

gradually.

Keep a face, hands and legs away from the

grease nipple.

For adjusting track shoe tension, see

"INSPECTING AND MAINTAINING TRACK

SHOE TENSION" in Chapter 4.

１

GENERAL GUIDELINES FOR WELDING

Welding work must be performed by a certified welder at a facility where welding devices are properly

equipped. Damage of electric parts, poisonous gas from paint due to heat of welding or a fire may

occur.

Basic Precautions for Welding

・

Turn the starter switch to the "OFF" position.

・

Disconnect the cable at the negative (-) terminal of the battery to cut off the current.

・

Attach welder ground cable within 1 m {3.3 ft.} from the part to be welded. If the welder ground

cable is attached to the area near electric parts/connectors, these electric parts/connectors may be

damaged.

・

Attach the welder ground cable directly to the area near the part to be welded and on the same

parent material.

・

Make sure that neither the bearing nor seal is positioned between the welder ground and the part

to be welded.

・

Do not attach the welder ground cable near the attachment pin or cylinder. It will damage plating.

・

Remove paint from any surface to be welded to avoid generating poisonous gas.

・

Always wear protective gears appropriate for welding.

・

Perform work in a well-ventilated areas.

・

Clear of combustible materials and provide a fire extinguisher in preparation for a fire.

SUPPORT WHEN JACK-UP

USE CAUTION WHEN ADJUSTING THE TRACK TENSION

［

1. SAFETY PRECAUTIONS

］

1-39

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды