Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 25 / 296

１

authorized dealer/distributor for assistance.

Before removing the crawler belt, confirm that the pressure inside the track tensioning cylinder

has been completely released.

Then turn the sprocket.

If the release of the pressure in the track tensioning cylinder is not carried out, grease can

penetrate skin, causing severe injury. If the tension of crawler belt does not reduced, call

KOBELCO authorized dealer/distributor for repair service.

23. Use caution to avoid breathing dust that may be generated when handling components containing

asbestos fibers. If this dust is inhaled, it can be hazardous to your health. Components of

manufacturers' products that may contain asbestos fibers are brake pads, brake band, brake lining

assemblies, clutch plates and some gaskets. The asbestos used in these components is usually

sealed in resin or by other ways. Normal handling is not hazardous as long as the dust containing

asbestos is not generated in the air.

If the dust containing asbestos is generated, there are several general guidelines that should be

followed.

Never use compressed air for cleaning.

Avoid brushing or grinding of asbestos containing materials.

When cleaning the machine, use wet methods or a vacuum equipped with a high efficiency

particulate air (HEPA) filter.

Use an ventilating fan when performing a long time machining work.

Wear the specified respirator if the dust is uncontrollable.

Comply with the rules and regulations applied on the working site.

Comply with the environmental rules and regulations on the disposal of asbestos.

Avoid areas where asbestos particles may be in the air.

［

1. SAFETY PRECAUTIONS

］

1-7

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды