Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 166 / 296

Clean each pin and pin bore and grease

sufficiently.

Move the bucket cylinder to align the pin

bores of bucket (6) and bucket link (8) with

each other, and then insert pin (4).

Raise the boom and slightly raise the

bucket from the ground.

Move arm (7) to align the pin bores of

bucket (6) and arm (7) with each other,

and then insert pin (5).

Insert pin (3) and install retaining ring (2).

Fit O-ring (1) in place.

Apply grease to the grease nipples for

each pin until the grease comes out

through the gap between pins and bore.

INSTALLING BUCKET

If O-ring (1) is cracked or has lost elasticity, replace it with a new one.

［

4. INSPECTION AND MAINTENANCE

］

4-24

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды