Kobelco SK35SR-6 Скачать руководство пользователя страница 13

Страница: 13 / 296

FOREWORD

AVOID A CHANCE OF SEVERE INJURY

Read, understand and follow all safety precautions and procedures found in this manual before

attempting any operation, inspection or maintenance of this machine, attachment or systems.

KOBELCO cannot anticipate every possible circumstance that might involve a potential danger. The

warnings in this publication and on the product are therefore not all inclusive. If a tool, procedure,

work method or operating technique not specifically recommended by manufacturer is used, you must

satisfy yourself that it is safe for you and others. You should also ensure that the product will not be

damaged or made unsafe by the operation, lubrication, maintenance and/or repair procedures you

choose.

GENERAL

・

This manual contains procedures to aid the operator gain peak performance through effective,

economical operation and maintenance of the machine.

・

Do not use this machine before you have read and understand safety, operation and maintenance

procedures described in this manual. Failure to follow them may lead to severe injury to persons

and/or facility failure.

・

Operators and persons working with this machine should continually study this manual until proper

safety, operation and maintenance procedures are completely understood.

・

This manual describes the basic operating techniques. Skill is gained as the operator utilizes these

techniques and completes them with an actual machine.

・

Some figures may be different from the actual machine. Along with KOBELCO technical

improvements, manuals are periodically updated to reflect these changes.

・

This manual may not contain attachments and optional equipment that are available in your area.

Please contact KOBELCO authorized dealer/distributor for any optional attachments/equipment

required.

・

The contents of this manual and operation of the machine are based on the use of KOBELCO

genuine manufacturer sourced parts. Replacement with non-genuine parts or modified parts is not

recommended.

・

Materials and specifications are subject to change without notice.

PERIODIC INSPECTION

・

After delivery of the machine, KOBELCO authorized dealer/distributor will make periodic inspections.

These inspections will be free of charge to the owner of the machine and will be performed at

time intervals set by KOBELCO. Contact KOBELCO authorized dealer/distributor for any service

related questions not explained in this manual.

NOTICE

・

Owing to the policy of continual improvement, changes may be made by KOBELCO to any of its

products without any obligation on the part manufacturer.

［

FOREWORD

］

0-3

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды