Kobelco SK35SR-6 Скачать руководство пользователя страница 282

Страница: 282 / 296

When the front attachment is installed, make

sure that the operation switch is in the "LOCK"

side before starting the engine.

Move the machine to a level ground and

lower the front attachment to the ground.

Set the quick hitch operation switch to the

"UNLOCK" side.

The quick hitch operation switch is

equipped with the sliding mechanism for

preventing an erroneous switch operation

(See 2.4.8 "QUICK HITCH OPERATION

SWITCH").

Movable hook (1) is actuated to release the

front attachment. The alarm sound starts as

soon as the switch is switched to the

"UNLOCK" side.

The alarm sound will not stop until the

quick hitch operation switch is at the

"UNLOCK" side.

Remove the front attachment.

HANDLING THE QUICK HITCH OPERATION SWITCH

8.5.3

REMOVING FRONT ATTACHMENT

Work on a stable and level ground to prevent the removed front attachment from tipping/rolling over.

Be sure to lower the front attachment to the ground before operating the quick hitch.

［

8. OPTIONAL EQUIPMENT

］

8-34

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды