Kobelco SK35SR-6 Скачать руководство пользователя страница 46

Страница: 46 / 296

Do not start the engine or touch the control

levers when the warning tags "DO NOT START

ENGINE!", "DO NOT OPERATE" or "UNDER

INSPECTION/MAINTENANCE", or a

tag with

the same kind of description is put on a control

lever or around the machine.

1.7

PRECAUTIONS FOR OPERATIONS

1.7.1

STARTING

STARTING ENGINE

ONLY ONE OPERATOR IS ALLOWED TO ENTER THE OPERATOR'S STATION.

Only one operator should be in the operator's station while operation. Allowing another person to ride

in the operator's station hinders your operation and may cause personal injury. Do not allow another

person to ride in the operator's station as well as on the machine body.

SEAT BELT

Fasten the seat belt securely to prevent hitting heavily to inside the cab, being thrown out of the cab

and being crushed under the machine when the machine tips/rolls over. If the seat belt is not

fastened, it may cause severe injury or death. Fasten it without fail whenever taking the seat.

Make sure that there is no abnormality on the attaching bracket and belt before fastening the seat

belt.

Replace the seat belts with new ones every 3 years even when damage or deterioration is not found.

PRECAUTIONS OF STARTING THE ENGINE

・

Move the pilot control shut-off lever to the "LOCKED" position.

・

Be sure to start the engine from the operator's seat.

・

Sound the horn before starting the engine to warn surrounding personnel that the machine is

being started.

・

Do not start the engine by short-circuit across the starter terminals or the battery. The machine

might move unexpectedly and the electric system might be damaged.

CHECK AFTER STARTING ENGINE

After starting the engine, check the performances of devices such as the bucket, arm, boom and dozer

(if equipped) and the performances of traveling and swinging.

Perform the check in a large space where there are no other persons and obstacles.

Failing to perform the check after starting the engine may cause late detection of a defect, resulting

in severe injury and damage to the machine.

When a failure is found, repair it immediately.

WARM UP

If the equipment/attachment is operated without enough warming-up running, the response of the

equipment/attachment to the control lever is delayed and sometimes it moves unexpectedly and

causes severe injury. Do not fail to warm up the machine. Especially in cold weather, the sufficient

warming-up is necessary.

［

1. SAFETY PRECAUTIONS

］

1-28

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды