Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 215 / 296

To change the gear oil of the idler, remove

the rubber track shoe on the side where the

gear oil is to be changed.

４

Idler

When removing/installing the rubber track shoe, lift up the machine on the side where the shoe is to

be removed/installed. It is very dangerous for the machine to fall unintentionally. Do not move

anything other than the track shoe to be removed/installed.

Idler

Remove the rubber track shoe. (See "REPLACING RUBBER TRACK SHOE" in Chapter 4. Be

sure to support the machine with a safety strut.) Stop the engine.

Pull out idler (1) and idler adjuster (2) from the crawler frame.

Mass: Idler + Idler adjuster = approximately 60 kg (132 lb)

Remove idler fuel inlet plug (3) with an Allen wrench to drain old gear oil.

Refill the specified amount {80 cc (4.9 cu

･

in)} of gear oil through the fuel inlet.

Wind a sealing tape around plug (3), tighten the plug securely, and then clean up any oil around

the plug.

Apply grease to sliding surface (A) between piston (4) and cylinder (5) of idler adjuster (2).

Attach the idler and idler adjuster (2) to the crawler frame with fill plug (3) and grease nipple (6)

facing outward.

Attach the rubber track shoe. For how to attach it, see "REPLACING RUBBER TRACK SHOE" in

Chapter 4.

Adjust the rubber track shoe tension. For how to adjust it, see "INSPECTING AND MAINTAINING

TRACK SHOE TENSION" in Chapter 4. Check the engagement and tension of the idler, and then

remove the safety strut supporting the machine to lower the machine.

［

4. INSPECTION AND MAINTENANCE

］

4-73

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды