Kobelco SK35SR-6 Скачать руководство пользователя страница 200

Страница: 200 / 296

The return filter needs delicate treatment

because it works as an important part in

removal of contaminant in the hydraulic oil to

prevent failure of hydraulic components and

maintain a long service life.

4.16

1000 HOUR (12-MONTH) INSPECTION & MAINTENANCE

PROCEDURES

Thoroughly read and understand "1. SAFETY PRECAUTIONS" of this manual before performing the

inspection and maintenance.

Follow this section together with daily, 50-hour, 250-hour and 500-hour inspection and maintenance.

4.16.1

REPLACING RETURN FILTERS

Immediately after the engine is stopped, the inside of the hydraulic oil tank is heated and pressurized

and it is very dangerous. Before removing the return filter, stop the engine and then press the valve

head on top of the breather cap to release the pressure in the hydraulic oil tank.

Wait for the hydraulic oil to cool down before the return filter replacement.

Replace the return filter with a new one after 50 hours of operation for the first time.

When the hydraulic breaker is attached, the deterioration of the hydraulic oil is faster than that of the

normal bucket digging work. Replace the return filter and hydraulic oil earlier than the specified time.

For the replacement interval (hours), see "PERIODIC INSPECTION AND MAINTENANCE CHART OF

NIBBLER (CRUSHER) AND BREAKER" in Chapter 7.

［

4. INSPECTION AND MAINTENANCE

］

4-58

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды