Kobelco SK35SR-6 Скачать руководство пользователя страница 88

Страница: 88 / 296

To lock an open door, fully open it until it

is locked into catch (2) in the rear of the

cab.

To close the door, pull lever (1) inside the

door to release the catch.

To open the door from the inside of the cab,

pull lever (1) to open the door.

2.10

OPERATOR CAB

LEAVING OPERATOR'S SEAT

When necessary to leave from the operator's seat, lock the pilot control shut-off lever.

If the control lever is unexpectedly touched without the pilot control shut-off lever locked, it may cause

severe accident resulting in severe injury.

2.10.1

CAB DOOR LOCK

This is used to fix door in the condition where the door is open.

In operation, lock the door securely either open side or close side. If not locked, the door may open

or close unexpectedly and this may cause danger and failure of the machine.

2.10.2

OPENING DOOR FROM INSIDE OF CAB

［

2. MACHINE FAMILIARIZATION

］

2-24

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды