Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 169 / 296

Repair or replacement of the rubber track shoes

is required if the following conditions are

observed. Contact KOBELCO authorized

dealer/distributor for repair or replacement.

1. Lower roller

2. Rubber track shoe

3. Lug

4. Steel cord

5. Core metal

As lug height (A) decreases due to wear,

the drawbar pull is reduced. When (A) is

5 mm (0.2 inch) or less, replace the

shoes with new ones.

When lugs are worn and steel cord (1)

inside the shoe is exposed across two links

or more, replace the shoe with a new one.

If lugs are worn and more than half of one

steel cord (B) is broken, replace the shoe with

a new one.

If cracking (A) of 60 mm (2.4 inch) or longer

occurs between lugs of the rubber track shoe,

repair it. In addition, if a shorter cracking (B)

occurs and inner steel cord (1) is exposed,

immediately repair it.

４

4.11.5

CHECKING RUBBER TRACK SHOE

LUG HEIGHT

BREAK OF STEEL CORD

CRACKING OF RUBBER TRACK SHOE

Contact KOBELCO authorized dealer/distributor for judgement of replacement or repair of the rubber

track shoe.

［

4. INSPECTION AND MAINTENANCE

］

4-27

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды