Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 110 / 296

Except for special cases, place the

attachment on the ground before stopping

the engine.

Place the pilot control shut-off lever in the

"LOCKED" position.

Move engine throttle lever (1) back to the

"low idle position" to idle the engine for

about 5 minutes.

Be sure to idle the engine which is hot

after operation to cool down the coolant

temperature.

Turn starter key (2) to the "OFF" position

to stop the engine.

Remove starter key (2).

3.5

STOPPING MACHINE ENGINE

To protect the engine, be sure to run the engine for 5 minutes with no load and low speed before

stopping the engine.

If the engine is stopped when it is running at high speed, the engine temperature rapidly rises, which

may cause a failure such as oil deterioration and seal adhesive.

Low idle position

［

3. MACHINE OPERATION

］

3-16

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды