Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 70 / 296

This indicates the amount of fuel. When there

is very little fuel left, the pointer points E.

Check the fuel level and refill. For fuel to use,

see "LUBRICANT, FUEL & COOLANT

SPECIFICATIONS" in Chapter 4.

1. White

2. Red

This warns of abnormal reduction of the

engine lubricating oil pressure. If it is lit, stop

the engine and check the engine oil level. See

"CHECKING ENGINE OIL LEVEL AND

REFILLLING" in Chapter 3.

This warns of abnormalities in the charging

system while the engine is running. It is lit

when you turn the starter switch ON. The

system is normal if it goes off after the engine

starts. If it does not go off after a while, it

means that the battery is not properly charged.

In that case, inspect the charging system. See

"INSPECTING AND MAINTAINING BATTERY"

in Chapter 4.

This warns of temperature abnormalities of the

engine coolant. If it is lit, stop the operation

immediately and run the engine at the idle

speed to cool it. Wait for the water to cool

down, stop the engine, and then check the

coolant level, tension of the fan belt and the

radiator core for clogging.

See "CHECKING COOLANT LEVEL FOR

SHORTAGE AND MAKING UP"in Chapter 3,

"CLEANING RADIATOR, OIL COOLER AND

FILTER", and "ADJUSTING FAN BELT

TENSION" in Chapter 4.

2.3.2

FUEL LEVEL METER

2.3.3

ENGINE OIL PRESSURE LAMP (LIT IN RED)

2.3.4

BATTERY CHARGE LAMP (LIT IN RED)

2.3.5

ENGINE COOLANT TEMPERATURE LAMP (LIT IN RED)

［

2. MACHINE FAMILIARIZATION

］

2-6

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды