Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 195 / 296

Inject grease until the old grease is pushed

out from the sealing surface of the swing

bearing for each of four directions while

swinging the machine by 90 degrees. The

greasing point is one (grease nipple).

Set the attachment in the greasing position

and then stop the engine.

Before greasing, wipe off the grease

nipples. Replace any damaged nipples

with new ones.

Use the grease gun to apply grease to

the grease nipples.

After applying grease, wipe off old grease

which is pushed out.

No.

Greasing point

Point

No.

Greasing point

Point

Dozer cylinder foot pin

Dozer foot pin

Dozer cylinder rod pin

４

4.14.7

GREASING SWING BEARING

Do not swing the machine while greasing the swing bearing.

4.14.8

GREASING DOZER

ATTENTION TO GREASING

For the digging work in the water, grease the submerged parts before and after the work every day.

Grease the machine before the work if it has not been used for one month or longer.

［

4. INSPECTION AND MAINTENANCE

］

4-53

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды