Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 26 / 296

1.3

WARNING LABEL

Labels for preventing danger are affixed to the certain areas of the machine where particularly require

the operator and personnel to pay attention for safety. Be familiar with the locations of warning labels

and the contents of preventing danger by taking enough time.

1.3.1

WARNING LABELS MAINTENANCE

・

Do not remove the affixed warning labels to this machine.

・

Confirm that all of these labels can be easily read.

・

If words or illustrations are illegible, clean off the dirt. Use a cloth, water and detergent to clean

the warning labels. Never use organic solvents or gasoline.

・

If warning labels are damaged, missing or illegible, replace them with new ones. Contact

KOBELCO authorized dealer/distributor for new warning labels.

・

There are labels other than those shown below, so handle them same as the contents mentioned

above.

1.3.2

LOCATION OF WARNING LABELS

［

1. SAFETY PRECAUTIONS

］

1-8

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды