Kobelco SK35SR-6 Скачать руководство пользователя страница 168

Страница: 168 / 296

Push rubber lock pin (3) into the hole of

the adapter nose.

Fit tooth point (2) onto adapter nose (5).

Hammer locking pin (4) until it is aligned

with the point surface.

Remove any sand and soil around the

attaching bolts, use an acetylene torch to

cut off the bolts, and then remove the side

cutters.

Clean the mounting surfaces and install

new side cutters.

When replacing the side cutters, replace

the bolts and nuts with new ones.

Tightening torque:

249.6 to 308.4 N

･

m (184 to 227 lbf

･

ft)

After tightening the nuts, spot-weld them.

INSTALLING THE TOOTH POINT

Align the rear face of the pin bore on the tooth point with that on on the adapter nose or insert the

tooth point more deeply.

REPLACING THE SIDE CUTTERS

If the replacement is delayed, the body of the bucket will be damaged.

Early replacement is recommended.

［

4. INSPECTION AND MAINTENANCE

］

4-26

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды