Kobelco SK35SR-6 Скачать руководство пользователя страница 21

Страница: 21 / 296

DANGER indicates a hazard with a high

level of risk which, if not avoided, will result

in death or severe injury.

WARNING indicates a hazard with a

medium level of risk which, if not avoided,

could result in death or severe injury.

Indicates a potentially hazardous situation

which, if not avoided, may result in minor

or moderate injury. It may also be used to

warn against possible damage to the

machine and its components.

１

1.1

GENERAL SAFETY INFORMATION

AVOID INJULY OR DEATH

Do not operate or perform any maintenance on this machine until all instructions found in this manual

have been thoroughly read and understood. Improper operation or maintenance of this machine may

cause accidents and could result in severe injury or death. Always keep this manual being stored in

the place provided on the machine.

If it is missing or damaged, place an order with KOBELCO authorized dealer/distributor for a

replacement. If you have any questions, please consult KOBELCO authorized dealer/distributor.

Most accidents in operation are due to non-observance of safety rules and precautions. Sufficient

care should be taken to avoid these accidents. Erroneous operation, lubrication method,

maintenance and inspection are very dangerous and may cause injury or death. Therefore all

precautionary measures, NOTES, DANGERS, WARNINGS and CAUTIONS contained in this

manual and on the machine should be read and understood by all personnel before starting any

work with or on the machine.

Operation, maintenance and inspection should be carefully carried out, and safety must be given

the first priority. Safety messages are indicated using the following warning symbols and signal

words. The safety information contained in this manual is intended only to supplement safety

codes, insurance requirements, local laws, rules and regulations.

It is very difficult to forecast every danger that may occur during operation. However, safety can

be ensured by fully understanding proper operating procedures for this machine according to

methods recommended in this manual.

While operating the machine, be sure to perform work with great care to avoid damage to the

machine, and accidents from occurring.

Continue studying this manual until all safety, operation, and maintenance and inspection

procedures are completely understood by all personnel working with the machine.

Icons used in this manual;

x (icon): This icon indicates an unacceptable practice or unsafe condition.

o (icon): This icon indicates an acceptable practice or safe condition.

All messages of safety used in this manual and the machine are identified by the words

"DANGER", "WARNING", "CAUTION" and "IMPORTANT".

［

1. SAFETY PRECAUTIONS

］

1-3

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды