Kobelco SK35SR-6 Скачать руководство пользователя страница 281

Страница: 281 / 296

Never perform any lifting work using quick hitch.

The lifted load may come off and cause severe

accidents.

Do not move heavy loads or lift up the machine

without a front attachment installed. The quick

hitch may have excessive load imposed and be

damaged.

When the quick hitch is installed, the operating

range is different from when a usual front

attachment is installed. Check for interference

before operation.

８

8.5

QUICK HITCH

The following precautions and descriptions about handling the quick hitch body is intended for the

machines with KOBELCO standard quick hitch installed.

8.5.1

PROHIBITED WORKS

LIFTING WORK

WORK WITHOUT FRONT ATTACHMENT

8.5.2

PRECAUTIONS

INTERFERENCE BY THE FRONT ATTACHMENT

［

8. OPTIONAL EQUIPMENT

］

8-33

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды