Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 146 / 296

4.2

INSPECTING AND MAINTAING THE MACHINE

4.2.1

GENERAL SAFETY & PRECAUTIONS

Do not use inspection and maintenance procedures other than ones described in this manual. Park the

machine on the level and firm ground before inspection and maintenance.

For the adjustment, disassembling and repair of the engine, reduction unit, hydraulic component and

electronic devices (controller, etc.), contact KOBELCO authorized dealer/distributor.

WEAR PROTECTIVE GEARS

Wear protective gears to avoid injury.

Wear a hard hat, protective glasses or face shield, work gloves, protective shoes and well-fitting

working clothes when performing inspection and maintenance procedures on this machine.

ALWAYS KEEP THE MACHINE CLEAN

Thoroughly clean the machine before performing inspection and maintenance procedures. It is easier

and safer to locate problems, perform maintenance and also reduce the risk of hydraulic system

contamination when machine is clean.

CHECK THE HOUR METER

Read the hour meter every day to check for items which get to the next inspection and maintenance

time.

STOP THE ENGINE BEFORE INSPECTION AND MAINTENANCE

Be sure to stop the engine before inspection and maintenance.

Inspecting and maintaining the running engine may cause injury by being caught in the cooling fan or

fan belts. When running the engine is unavoidable during the inspection or maintenance, it should be

done by at least two persons communicating each other, of which one can stop the engine at any

time.

PUT THE WARNING TAGS

Put the tags "DO NOT START ENGINE!", "DO NOT OPERATE" and "UNDER

INSPECTION/MAINTENANCE" on noticeable places such as around the operator's seat as well as the

starter switch or control levers before inspection and maintenance.

COMPLY WITH THE PRECAUTIONS

Read and understand the warning labels on the machine before starting the inspection and

maintenance.

［

4. INSPECTION AND MAINTENANCE

］

4-4

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды