Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 77 / 296

When the pilot control shut-off lever is set to

the "LOCKED" position, the hydraulic system is

shut down.

When the lever is set to the "UNLOCKED"

position, the hydraulic system is unlocked.

２

2.5.2

PILOT CONTROL SHUT-OFF LEVER

The pilot control shut-off lever is provided to prevent any unexpected operation due to unexpected

contact with the left/right control levers or travel levers.

HANDLING OF PILOT CONTROL SHUT-OFF LEVER

Do not stand up and move during operation or unexpected contact with the control levers may cause

a sudden movement of the machine. Be sure to raise the pilot control shut-off lever to the "LOCKED"

position and set the boom swing foot pedal to the "LOCKED" position before standing up or moving.

Setting the pilot control shut-off lever to the "LOCKED" position does not lock the boom swing foot

pedal.

Set the pilot control shut-off lever to the "LOCKED" position securely, or it may not be locked.

Make sure that the pilot control shut-off lever is held to the "LOCKED" position shown in the figure

below.

When unlocking, do not touch other levers unintentionally. Touching other levers may cause danger

due to unexpected machine movement.

After completion of work or during transportation, hold the pilot control shut-off lever to the "LOCKED"

position.

Locking hydraulic system (A)

"LOCKED" position

Unlocking hydraulic system (B)

"UNLOCKED" Position

［

2. MACHINE FAMILIARIZATION

］

2-13

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды