Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 60 / 296

Wear protective glasses, long-sleeve shirt and

rubber gloves when handling or servicing

batteries.

Battery electrolyte contains dilute sulfuric acid. If

battery electrolyte contacts skin or eyes, flush

affected areas immediately with a large amount

of fresh water because it may cause blindness

and burns and seek medical attention.

・

Batteries give off hydrogen gases that can

explode and cause personal injury.

Definitely keep open flames and cigarettes

away from batteries.

・

Keep all ventilation caps tightly secured.

・

Be sure to connect the terminals securely.

・

When charging the battery, remove it from

the machine and remove the ventilation

caps to allow gas to escape in a

well-ventilated area.

・

Do not charge the frozen battery

because it could explode. To prevent the

explosion, heat it up until the battery

temperature becomes 16 degrees C or

higher.

・

Do not use or charge the battery of which

the battery electrolyte level is lower than

the lower limit. This might cause

explosion. Check the battery electrolyte

level periodically, and make up the loss

with distilled water to the proper limit of the

electrolyte level.

1.9

HANDLING BATTERY

1.9.1

PREVENTION OF BATTERY ELECTROLYTE BURNS

1.9.2

PREVENT BATTERY EXPLOSIONS

1.9.3

REPLACING THE BATTERY

・

Always disconnect the negative (-) cable first when disconnecting the battery cables. On the

contrary, always connect the positive (+) cable first when reconnecting the battery cables.

・

Never put tools between the battery positive (+) terminal and the machine. The short circuit and

spark will occur.

・

Do not mistake in the jumper cable connection.

Never connect the positive (+) terminal to the negative(-) terminal. Finally, connect the negative (-)

terminal to the upper frame of the machine.

See "USING JUMPER CABLES" in Chapter 3 for the starting procedures of using jumper cables.

［

1. SAFETY PRECAUTIONS

］

1-42

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды