Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 167 / 296

Check the bucket tooth points and side cutters

for wear. A tooth point with holes or crackings

should be replaced before adapter (1) begins to

be worn.

A side cutter with severe wear should be

replaced soon after it is found. If the

replacement is delayed, the body of the bucket

will be damaged.

1. Adapter

2. Tooth point

3. Rubber lock pin

4. Locking pin

5. Adapter nose

To hammer out the tooth pin, place the

bucket on safety block (6), making the

tooth parallel to the ground.

Using hammer (7) and punching tool (8),

hammer out locking pin (4). Be careful not

to break rubber lock pin (3).

Inspect locking pin (4) and rubber lock pin

(3). If locking pin (4) is too short or rubber

lock pin (3) is in poor condition as shown

to the right, replace it with a new one.

４

4.11.4

REPLACING TOOTH POINT AND SIDE CUTTER

When replacing a tooth point or side cutter, apply a safety block to the bottom face of the bucket.

REPLACING THE TOOTH POINTS

When replacing the tooth points or the side cutters, contact KOBELCO authorized dealer/distributor.

When hammering, metal chips can fly. If it flies into the eye, it may result in severe injury. Wear

protective gears such as protective glasses, hard hat and gloves.

REMOVING THE TOOTH POINT

［

4. INSPECTION AND MAINTENANCE

］

4-25

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды