Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 73 / 296

The switch located on the grip of the right

travel lever can be used to select HIGH (2nd)

or LOW (1st) travel speed. Turning the starter

switch "OFF" from "ON" automatically sets the

travel speed to LOW.

Set to LOW (turtle) when traveling on soft

surfaces, slopes, or in a narrow place, or

when powerful drawbar pull is required.

Set to HIGH (rabbit) when traveling on the level

and firm ground.

For travel speed, see Chapter 6 "GENERAL

SPECIFICATIONS".

This switch is used to turn on the working

lights on the boom and canopy.

"OFF" position:

"ON" position:

The working lights on the boom and canopy

are lit.

The horn sounds while the switch located on

the top of the left control lever grip is being

pressed.

２

2.4.2

TRAVEL SPEED SELECT SWITCH

The travel speed should be set to LOW when the machine is running on the downhill, or loading

on/unloading from a truck or trailer. A sudden change of the machine stability may cause tipping/rolling

over.

2.4.3

WORKING LIGHT SWITCH

2.4.4

HORN SWITCH

Be sure to sound the horn before starting this machine to warn surrounding personnel.

［

2. MACHINE FAMILIARIZATION

］

2-9

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды