Kobelco SK35SR-6 Скачать руководство пользователя страница 210

Страница: 210 / 296

Remove the rubber boot of the control

lever, referring to "LUBRICATING PUSH

ROD OF CONTROL LEVER" in Chapter 4.

To remove cover (5) of the left side lever,

loosen two bolts (8) and remove cover (5).

To remove cover (6) of the right side lever,

loosen two bolts (9) to remove cover (7),

and then loosen three bolts (8) to remove

cover (6).

4.18.3

CLEANING PILOT LINE FILTER

Internal pressure always exists in the hydraulic circuit. Do not inspect or maintain the machine before

releasing the internal pressure.

To release the internal pressure of the hydraulic oil tank, press the valve on top of the breather cap

to release the pressure in the hydraulic oil tank.

Wipe off spilled hydraulic oil to prevent a fire.

On each "P port" of the pilot valves for left and right hand operator control levers, the pilot valve for

travel, and the solenoid valve, the filtered connector is attached. If dust is adhered to these filters, the

flow of hydraulic oil will be interrupted. If dust enters into the valves, it may cause failure. Remove

them periodically to clean them.

When cleaning the pilot line filters, place the machine in the parking position, set the pilot control

shut-off lever to the "LOCKED" position, and stop the engine. Then bleed the air of the hydraulic

circuit, referring to "RELEASING INTERNAL PRESSURE IN HYDRAULIC OIL AND HYDRAULIC

SYSTEM" in Chapter 4.

PILOT VALVES FOR CONTROL LEVERS

Left Side Lever

［

4. INSPECTION AND MAINTENANCE

］

4-68

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды