Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 172 / 296

Use the boom or arm to lower the bottom

of the bucket to the ground to lift the

machine body up. Be sure to perform the

lever operation slowly.

Support the undercarriage with safety strut

(1) or other means.

Loosen grease nipple (1) of the grease

cylinder slowly to drain the grease.

Loosen grease nipple (1) gradually within

one turn at most.

Put in iron pipes along the rubber track

shoe and slowly rotate the sprocket in the

reverse direction. If the rubber track shoe

comes off from the iron pipes, slide it

horizontally to remove it.

Iron pipe

Rotation direction

Use the boom or arm to lower the bottom

of the bucket to the ground to lift the

machine body up.

Be sure to perform the lever operation

slowly.

Support the undercarriage with safety strut

(1).

Removing Rubber Track Shoe

Installing Rubber Track Shoe

［

4. INSPECTION AND MAINTENANCE

］

4-30

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды