Kobelco SK35SR-6 Скачать руководство пользователя страница 196

Страница: 196 / 296

After the radiator cap has cooled enough to

touch with bare hands, remove cap (1).

Loosen cap (1) slowly to release the

pressure, then push cap (1) down and

loosen it to remove it.

Inspect locations A through C for foreign

materials and damage to cap (1). Use a

clean cloth to wipe cap (1) and replace it if

necessary.

Inspection locations

A. Contact surface between negative

pressure valve (2) and gasket (5)

B. Both surfaces of pressure valve (3) and

gasket (5)

C. Both surfaces of external lid (4) and

gasket (6)

Securely tighten cap (1).

4.14.9

CLEANING AND REPLACING THE RADIATOR CAP

HANDLING OF RADIATOR CAP

Inside the radiator, the high pressure steam occurs and it may cause personal injury.

Do not loosen or remove the radiator cap when the coolant is under high pressure and temperature.

Stop the engine before removing the radiator cap.

Allow enough time for the coolant to cool down before removing the radiator cap.

A loose radiator cap will let hot steam and coolant escape from the cooling system during operation

and it may cause burns.

Radiator Cap (1)

［

4. INSPECTION AND MAINTENANCE

］

4-54

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды