Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 98 / 296

Coolant water reserve tank (1) is located

on the right rear side of the machine.

Open the engine food with the starter key

and check that the coolant level falls

within the range of FULL - LOW of

reserve tank (1). If the water level is low,

remove filler cap (2) of the reserve tank

and pour coolant water to FULL level.

After supply, tighten the cap securely.

If the reserve tank is empty, check it for

water leaks and check the water level in

the radiator. If the water level is low, fill the

radiator with water and then fill the

reserve tank with water. Then immediately

contact KOBELCO authorized

dealer/distributor for assistance.

Close the engine food and lock it with the

starter key.

3.2

CHECK BEFORE STARTING ENGINE

The following checkup should be performed once before the first engine startup in a day.

3.2.1

CHECKING COOLANT LEVEL FOR SHORTAGE AND MAKING UP

HANDLING OF RADIATOR

Do not open radiator cap if not required.

Check coolant level of the reserve tank (1) when engine is cooled down.

After the engine stops, the coolant is hot and the high pressure is accumulated in the radiator.

Removing the radiator cap under this condition may cause burns.

Allow the engine to cool down before removing the radiator cap.

If the water level in the reserve tank drops frequently, immediately contact KOBELCO authorized

dealer/distributor for assistance.

If the engine coolant temperature lamp is lit on the monitor panel when the engine is running or

when the engine switch is turned ON, loosen the radiator cap and pour coolant water to the neck of

the radiator cap. Then contact KOBELCO authorized dealer/distributor for assistance.

Be sure to check the coolant level on the cold engine before starting it. While the engine is warmed,

an accurate water level cannot be get since the radiator water moves to the reserve tank due to a

rise in water temperature. As the engine is cooled, the water level returns to normal.

［

3. MACHINE OPERATION

］

3-4

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды