Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 219 / 296

Place a container for drain oil under drain

plug (1) on the bottom of the hydraulic oil

tank.

Loosen drain plug (1) on the bottom of

hydraulic oil tank slowly and drain

hydraulic oil completely.

10. Clean drain plug (1) and install it in place.

Tightening Torque: 98 to 118 N

･

m (72.6

to 87.4 lbf

･

ft)

11. Refill hydraulic oil through fuel inlet (F) on

the top of the hydraulic oil tank.

Pour the oil while checking the oil level

with level gauge (G).

12. Attach filler port cover (4) with bolt (3).

Tightening Torque: 20.7 to 25.3 N

･

m (15.3

to 18.7 lbf

･

ft)

13. Start the engine, run it at low idle for

several (5 to 7) minutes. After that,

operate each cylinder extension and

retraction and swing the machine to return

it to the hydraulic oil inspection position.

Stop the engine and check the oil level,

and if it is low, add the hydraulic oil.

４

［

4. INSPECTION AND MAINTENANCE

］

4-77

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды