Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 262 / 296

・

The operating time is accumulated only

when the engine in running.

・

It is displayed in the unit of 0.5 hr.

If the operating time of a day is less than

0.5 hr (30 minutes), it is displayed as "0.0".

・

No operation day (when the engine was

not started) is displayed as a blank.

・

You can see the operating information of

the current month + past three months.

Older operating information than that is

deleted.

･

The recommended replacement time of the engine oil is 250 hr. The multi-display warns of it without

a buzzer.

･

The recommended replacement time of the fuel filter is 500 hr. The multi-display warns of it without a

buzzer.

･

The recommended replacement time of the hydraulic oil filter is 1000 hr. The multi-display warns of

it without a buzzer.

･

The recommended replacement time of the hydraulic oil is 5000 hr. The multi-display warns of it

without a buzzer.

OPERATING CONTROL SCREEN

This screen displays the operating time of each day in the unit of 0.5 hr (less than 0.5 hr are rounded

down).

You can see the operating information of total four months (current month and past three months).

For information on how to check the operating control, see "MENU SWITCH".

DISPLAY CONTENTS

1. Displays the month.

2. Displays the date with the blue background.

3. Displays the operating time of the day.

* The above figure shows a case where the machine operated for 1.5 hr on June 1st.

If the battery is removed, the stored data is cleared and all operating information will be displayed as

blank.

The initial state is "January 1st, 2000". Note the operating time before removing the battery or

changing the clock setting, if necessary.

［

8. OPTIONAL EQUIPMENT

］

8-14

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды