Kobelco SK35SR-6 Скачать руководство пользователя страница 124

Страница: 124 / 296

1. Left control lever

A. Swing right

B. Swing left

3.9.8

SWING PROCEDURE

There may be a risk of the machine losing the balance to tip/roll over during swinging when

operating on a slope.

Keep the machine and its attachment a safe distance from surrounding persons or facilities before

swinging the machine.

Move the pilot control shut-off lever to the "UNLOCKED" position.

Raise the bucket to a proper height from the ground.

Operate left control lever (1) to swing the machine.

While you are not swinging the machine, keep the attachment and crawler frame parallel to each

other before stopping or traveling the machine. Except for special cases, keep them parallel during

traveling.

［

3. MACHINE OPERATION

］

3-30

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды