Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 242 / 296

The positions as shown in the right figure make

the machine unstable and have a risk of falling.

Never perform the breaker work in these

positions.

A. Allowed work facing forward

B. Allowed work facing backward

C. Prohibited work facing sideways

PROHIBITION OF BREAKER WORK IN A SWING OR OFFSET POSITION

HYDRAULIC BREAKER WORK

Use the forward-looking or rearward-looking position without swing or offset for the hydraulic breaker

work.

Even if you use an attachment other than the hydraulic breaker, see "PROHIBITED WORK IN USE

OF BREAKER".

Use the reinforced arm with the hydraulic breaker. The breaker work with the standard arm may

cause damage to the arm.

［

7. NIBBLER (CRUSHER) AND BREAKER

］

7-6

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды