Kobelco SK35SR-6 Скачать руководство пользователя страница 148

Страница: 148 / 296

INSTALL LOCK DEVICE

When inspecting or maintaining the machine under the attachment, install a safety block and/or safety

strut to avoid its move and fall.

Change of clearance could lead to severe injury.

PRECAUTIONS IN REPLACING THE BUCKET

Do not insert your fingers into a pin bore.

When aligning the pin with a pin bore, never insert your fingers, hands, or arm into it.

Align the pin with a bore visually.

IN DUSTY WORKING SITE

Pay attention to the followings in dusty sites.

・

Check the air cleaner for clogging. Clean the air cleaner element earlier.

・

Clean the radiator core earlier to prevent the clogging.

・

Clean and replace the fuel filter earlier.

・

Clean the electrical components, especially the starter and generator, to prevent the accumulation

of dust.

［

4. INSPECTION AND MAINTENANCE

］

4-6

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды